Berikut ini saya sedikit share beberapa kode error Mesin FotocopyRicoh , kali ini spesifik mesinnya mp 2550 secara garis baesar sama dengan type FotocopyRicoh Black/White lainnya
SC 101-1 : Exposure lamp error 1
The standard white level could not be set properly when scanning the white plate during
automatic white level adjustment.
SC 101-2 : Exposure lamp error 1
The standard white level setting dropped below the specified range during scanning.
SC 120 : Scanner home position error 1
The scanner HP sensor did not turn off during scanner initialization or copying.
SC 121 : Scanner home position error 1
The scanner HP sensor did not turn on during scanner initialization or copying.
SC 141 : Black level correction error
- Harnesses at the SBU, IPU, BCU loose, broken, defective.
- Black level correction could not be set properly during automatic adjustment.
SC 142 : White level correction error
White level correction could not be set properly during automatic adjustment.
SC 143 : SBU auto adjust error
The machine could not acquire the white or black peak level setting at power on.
SC 144-1 : SBU connection error
Connection to the SBU could not be confirmed, possibly due to a defect in the BCU
detection board
SC 144-2 : SBU serial communication error
Poor SBU power supply caused by SIO, or BCU detection board defective.
SC 144-3 : SBU GASBU reset error
SBU defective, BCU detection circuit defective.
SC 144-4 : SBU version error
SBU defective, BCU detection circuit defective.
SC 161 : IPU Error
The self-diagnostic test detected an error at
the IPU at power on, or after the machine
returned from energy save mode.
SC 165 : Copy Data Security Unit error •
SC 202 : Polygon motor error 1: ON timeout
The polygon mirror motor did not reach the targeted operating speed within 10 sec. after
turning on or changing speed
SC 203 : Polygon motor error 1: OFF timeout
The polygon mirror motor did not leave READY status within 3 sec. after polygon motor
switched off.
SC 204 : Polygon motor error 1: XSCRDY signal error
The XSCRDY signal remained HIGH for 200 ms while the LD unit was firing.
SC 220 : Laser synchronization detection error: LD0
The laser synchronizing detection signal for
the start position of the LD was not output for
two sec. after LDB unit turned on with the
polygon motor rotating normally.
SC 230 : FGATE ON error
The FGATE signal did not assert within the
prescribed time. (The BCU generates the FGATE
signal and sends it to the LD unit when the
registration sensor switches on.) • BCU, Controller board
harness loose or broken
SC 231 : FGATE OFF error
The FGATE signal did not go off within the
prescribed time. (The BCU generates the FGATE
signal and sends it to the LD unit when the
registration sensor switches on.)
SC 240 : LD error
The IPU detected a problem
at the LD unit.
SC302 : Charge level output error
The PWM output level was detected higher
than 50% after 10 consecutive samplings.
SC 350 :ID sensor calibration – Error 1
One of the following conditions occurred when the ID sensor pattern was calibrated
during printing:
Vsp > 2.5V
Vsg < 2.5V
Vsp = 0V
Vsg = 0V
SC 351 : ID sensor calibration – Error 2
The following conditions occurred simultaneously when the ID sensor pattern was
calibrated during printing:
Vsg = 5V
PWM = 0 (LED current drop)
High voltage power supply board (power pack) defective
353 B ID sensor LED current error
Error occurred during automatic
adjustment of Vsg:
ID sensor dirty or defective
SC 354 : ID sensor adjustment timeout error
Error occurred during automatic
adjustment of Vsg. Vsg could not
be adjusted to 4.0V ±0.2V
within the prescribed time.
SC 355 : ID sensor error
For more details about the cause
of the problem, please refer to
SC350 to SC 354 above.
• ID sensor dirty or defective
• ID sensor harness disconnected, or connector damaged
• BCU defective
• High voltage power supply board (power pack) defective
SC 389 : TD sensor error 1
TD sensor output was less than 0.5V, or more than 0.5V 10 times in succession. If the fax
unit is installed, this SC is issued immediately. If the fax unit is not installed, this SC is issued
after the prescribed number of copies has printed.
SC 390 : TD sensor error 2
The TD sensor outputs less than 0.5V or more than 4.0V 10 times consecutively during
copying.
Note: If the fax option is installed, this SC is issued immediately.
If the fax option is not installed, this SC is issued after the prescribed number of pages is
copied.
SC 391 : Development bias leak
A development bias leak signal is
detected.
SC 392 : TD sensor initial setting error
Initialization of the new PCU unit
failed (the drum and development
roller did not start rotating).
SC 401 : Transfer roller leak error 1
A transfer roller current leak signal wad detected. (The current feedback signal for the
transfer roller was not detected within the correct time.)
SC 402 : Transfer roller leak error 2
A transfer roller current leak signal is detected.
The current feedback signal for the transfer
roller is not detected within the correct time.
SC 411 : Separation bias leak error
A separation bias leak signal was detected.
SC 490 : Toner supply motor leak error
More than 1 ampere supplied to the toner
supply motor for longer than 200 ms.
SC 500 : Main motor lock
The machine detected motor lock (motor is not
operating correctly)
SC 541 : Fusing thermistor open (center)
The temperature of the hot roller remained below 0oC for
5 sec at the center of the hot roller.
SC542 : Fusing temperature warm-up error (center)
The fusing temperature did not reach the standby temperature within 20 sec. at the
center of the hot roller after the main switch turned on.
SC 543 : Fusing overheat error 1 (center)
The fusing thermistor detected a fusing temperature over 230 °C for 5 sec. at the
center of the hot roller.
SC 544 : Fusing overheat error 2 (center)
A fusing temperature over 250 °C is detected at the center of the hot roller by the fusing
temperature monitor circuit in the BCU board.
The power was interrupted for more than 0.3 sec.
SC 545 : Fusing overheat error 3 (center)
After warmup, the center of the hot roller attained full operating temperature and
maintained this temperature for 10 sec.without the hot roller rotating.
SC547 : Zero cross signal detection error
Zero cross signals were not detected within the prescribed time.
KLO ERROR INI COBA DIRESET DENGAN CARA
TEKAN C (CLEARMODE=KUNING) . 1. 0. 7. C(CLEAR=ORANGE) TAHAN 3 DETIK SAMPAI LAYAR BERUBAH, LALU MATIKAN POWER UTAMA
Lebih lengkapnya buat support ricoh bisa kunjungi
http://ricoh.com/downloads/
